Heavy industry Archives - Pietro Fiorentini

LDB171

Anna Veronesi — Thu, 20 Jun 2024 12:05:21 +0000

LDB171 is a new silencer option for Reflux/Reval regulators. The silencer LDB171 allows reducing the noise that is generated in the pressure regulator during the lamination process. Its efficiency is due to the fact that noise reduction takes place at the same point where it is generated, thus preventing its propagation.

It can be used with the following regulators:

The post LDB171 appeared first on Pietro Fiorentini.

Pilot series 210/A

Anna Veronesi — Tue, 05 Mar 2024 06:59:49 +0000

The pilot series 210/A is a mechanical device which enables the working principle and the setpoint modifications of pilot operated gas pressure regulators. The pilot is optimized to enhance the accuracy and minimize the lock-up performances.

This model specifically allow to have a fail-to-open regulator in case of pilot’s failure.

It can be used with the following regulators:

The post Pilot series 210/A appeared first on Pietro Fiorentini.

GEDRA

Anna Veronesi — Wed, 13 Sep 2023 07:27:21 +0000

GEDRA (Gas Energy Density Raman Analyser) is a real time gas analyser tailored for natural gas, biomethane, and hydrogen analysis.

The decarbonization of gas supply and subsequent reconfiguration of gas flows through the grid will substantially affect the gas network operator business. The shared goal is to increase the use of alternative green gas sources such as biogas, biomethane and hydrogen-enriched natural gas.

In this future with a such heterogeneous gas network, GEDRA will play a crucial role on the way to renewables in monitoring fundamental gas parameters. It measures a wide range of gas mixtures without any hardware reconfiguration or any needs of consumable supplies, ready for remote monitoring and control.

Designed to withstand harsh environmental conditions, GEDRA can be installed anywhere along the gas pipelines, including remote unmanned locations. Thanks to its peculiar features, it represents an effective alternative to gas chromatographs for monitoring calorific value.

The post GEDRA appeared first on Pietro Fiorentini.

Pulsation dampener

Anna Veronesi — Mon, 28 Aug 2023 07:39:52 +0000

The pulsation dampener is used in cases of unstable pneumatic signal in the sensing line. This accessory helps smooth out abnormal pulsations or spikes and improve regulator performance.

It is often installed when it is not possible to comply with the distance between the regulator and the sensing line connection recommended by the manufacturer or when the downstream line size (diameter) is too small, generating excessive turbulence due to high velocity.

This accessory helps to minimize pilot’s contamination from gas dirt and is suitable for natural gas and all non-aggressive gases applications.

The post Pulsation dampener appeared first on Pietro Fiorentini.

Filters for low pressure applications

Anna Veronesi — Tue, 27 Jun 2023 12:43:37 +0000

Thanks to the high filtration capacity of the cartridges and their broad surface, the cartridge filters by Pietro Fiorentini allow separation of both dust and solid particles.

Suitable for use with natural gas, LPG and non-corrosive gases, these devices are mainly used for low-pressure gas distribution networks.

The post Filters for low pressure applications appeared first on Pietro Fiorentini.

Pilot series 200/A

Anna Veronesi — Thu, 22 Jun 2023 08:51:37 +0000

The pilot series 200/A is a mechanical device which enables the working principle and the setpoint modifications of pilot operated gas pressure regulators. The pilot is optimized to enhance the accuracy and minimize the lock-up performances.

According to the European Standard, it is classified as Fail To Open.

It can be used with the following regulators:

The post Pilot series 200/A appeared first on Pietro Fiorentini.

Terval AP

Dario Zoppelletto — Wed, 21 Dec 2022 07:19:14 +0000

Terval AP is a three-in-one pilot-operated gas pressure regulator.

It is particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks, and it can be used with previously filtered non-corrosive gases.

Terval AP according to the configuration can be classified as Fail Close or Fail Open according to the European Standard EN 334.

Terval AP is Hydrogen Ready for NG-H₂ blending.

The post Terval AP appeared first on Pietro Fiorentini.

Starbox LX2

Anna Veronesi — Fri, 11 Nov 2022 15:03:09 +0000

Starbox LX2 is an innovative RTU Linux based, specifically designed for remote station control in harsh environmental conditions.

Starbox LX2 embodies the typical characteristics of a data logger with advanced multimedia features. In fact, it is a system where process control, multimedia capabilities, remote management and the internet are available and usable with identical operating standards and can be activated in a simple and intuitive way.

The post Starbox LX2 appeared first on Pietro Fiorentini.

MPower

Anna Veronesi — Fri, 06 May 2022 10:32:17 +0000

Mpower is an intrinsically safe associated apparatus designed to remotely supply devices of Modus and Mlog family in ATEX Zone 0 classified areas.

Mpower comes in two models, according to the selected primary energy source:

Mpower-PP: PV and microturbine;
Mpower-INS: AC mains – outage of primary power source is remotely signaled to device in hazardous area.

Both models can be supplied in wall mounting (IP65) or DIN rail (IP20) versions.

The post MPower appeared first on Pietro Fiorentini.

MLog Plus

Anna Veronesi — Fri, 06 May 2022 10:11:59 +0000

Mlog Plus is a gas datalogger specifically designed to support IoT applications such as distribute monitoring of reducing pressure stations along the gas network.

Mlog Plus is suitable for installation in ATEX Zone 0 classified areas, making it the ideal solution for a wide range of applications.
Mlog Plus commincates with the centralised data collection system (SCADA) using communication protocols such as Modbus, IEX 60870-5-104 and optionally LoRaWAN.
Device configuration supports 2g, GSM/GPRST and LoRaWAN communication modules for a seamless integration into Smart City cloud architectures.

The post MLog Plus appeared first on Pietro Fiorentini.

Modus Slim2

Anna Veronesi — Fri, 06 May 2022 09:39:51 +0000

Modus Slim2 is a MID certified Electronic Volume Converter with integrated communication module suitable for installation in ATEX Zone 0 classified areas.

Modus Slim2 is designed to be remotely controlled by the centralised data collection system (SCADA/SAC) using UNI TS 11291-3 (CTR) communication protocols.

Modus Slim2 is a MID certified PTZ Electronic Volume Converter supporting the acquisition of a pulse input from the gas meter and pressure and temperature measurements through integrated sensors.

The post Modus Slim2 appeared first on Pietro Fiorentini.

Modus

Anna Veronesi — Fri, 06 May 2022 07:20:27 +0000

Modus is a MID certified Electronic Volume Converter with integrated communication module suitable for installation in ATEX Zone 0 classified areas.

Modus manages up to 2 PTZ channels with dedicated inputs for the acquisition of pulse inputs from primary gas meter, pressure and temperature measurements. Moreover, the device provides additional input channels to support extended station monitoring applications.

Modus is designed to be remotelycontrolled by the centralised data collection system (SCADA/SAC) using communication protocols such as Modbus and UNITS 1129-3 (CTR) protocols.

The post Modus appeared first on Pietro Fiorentini.

Inspection agency – periodic verification

Digital Team — Wed, 05 May 2021 12:46:31 +0000

Periodic verification consists in ascertaining the maintenance over time of the metrological reliability of measuring instruments aimed at the protection of public trust.

Pietro Fiorentini created a completely independent division to perform the periodic verifications, provided for by Italian D.M. n. 93 of 21 April 2017, “Regulation concerning the criteria for the execution of subsequent metrological controls on gas meters and volume conversion devices“.

Pietro Fiorentini inspection agency complies with the requirements of UNI CEI EN ISO/IEC 17020: 2012, and is therefore accredited as a Type C Inspection Body for the periodic verification of gas meters and volume conversion devices associated with gas meters. This accreditation allows to perform maintenance activities at the same time of the periodic verification activity.

Pietro Fiorentini inspection agency is structured to respond to every need throughout the national territory; in fact, thanks to three Territorial Units located in the North-West, North-East and South, it can easily reach any location around Italy.

The Organization bases its activity on objective evidence obtained through an impartial, fair, valid and reliable evaluation, not influenced by other interests and without prejudice.

The organization is structured with tools that allow the execution of all activities with a very high degree of automation; moreover, each inspector is provided with his own digital electronic signature with which he validates the verification reports; thanks to an automated process, the documents are transferred to the attention of the Technical Manager of the Body who checks them and validates them with his own digital electronic signature in real time.

All the activities carried out by the inspectors can be evidenced by photographic documentation which is always filed together with the relevant inspection report.

The post Inspection agency – periodic verification appeared first on Pietro Fiorentini.

Spare parts support

Digital Team — Thu, 04 Mar 2021 12:03:31 +0000

Pietro Fiorentini After Sales Department provides original and high quality spare parts support service ready for a fast delivery all over the world, together with a dedicated technical service to help the customer finding the right replacement for every need.

The post Spare parts support appeared first on Pietro Fiorentini.

Tailored courses

Digital Team — Thu, 04 Mar 2021 12:02:48 +0000

Pietro Fiorentini provides tailored courses to its customers, adapting the training programs to specific requirements. These courses are available in every language and are specifically designed by our Training Department together with the customer to develop a focused learning path in accordance with the specific professional and technological needs.
Tailored courses can be held in our PF Gas Academy in Arcugnano (Vicenza), by the customer’s premises or online.

The post Tailored courses appeared first on Pietro Fiorentini.

PF Gas Academy courses

Digital Team — Thu, 04 Mar 2021 12:02:21 +0000

Handling natural gas demands high levels of knowledge. Mechanics, physics, together with regulations and laws are just a part of the required know-how for gas professionals on whose tasks depend the safety of all communities around the world.
Pietro Fiorentini, thanks to its experience in designing, manufacturing and installing solutions for the safe handling and management of natural gas, established PF Gas Academy, an internal Training Division which delivers a range of courses in every language specifically addressed to companies willing to instruct their professionals in all the aspects of a compliant installation and maintenance of gas regulating devices such as pressure regulators and complete systems.
PF Gas Academy in Arcugnano (Vicenza) is an avantgard school where our teachers are ready to share their knowledge on Pietro Fiorentini equipment, and our Gas Academy secretariat will be ready to help the companies supporting their stay in our premises.

The post PF Gas Academy courses appeared first on Pietro Fiorentini.

Electronic and metering maintenance

Digital Team — Thu, 04 Mar 2021 11:59:06 +0000

The maintenance of the electronic measurement and remote control equipment of the cabins includes both the evaluation of the state of wear of the components, such as the battery charge level, and the calibration of the pressure and temperature sensors, in the case of converters or dataloggers, or of the voltage and current channels in the case of other equipment. This on-sise service by Pietro Fiorentini also includes verification of the correct operation of alarm systems with error simulation. Issue certifications in compliance with current regulations are provided by qualified personnel.

The post Electronic and metering maintenance appeared first on Pietro Fiorentini.

Chemicals and odorizing

Digital Team — Thu, 04 Mar 2021 11:58:07 +0000

Pietro Fiorentini, thanks to the long and consolidated experience in the supply of odorization systems, provides innovative chemicals and odorizing to respond to the needs of any gas utility.
Having reliable data is the base of efficient operations and, through the analysis service, we can provide readings of the concentration of odorant in the different part of the network facilitating the setting of optimal odorization rate at the source or deciding if additional injection points are necessary. All readings are carried out according to latest European standards through sophisticated portable instruments. The analysis certificate is a precious evidence that gas is properly detectable in any point of the network.

The post Chemicals and odorizing appeared first on Pietro Fiorentini.

Operations & maintenance

Digital Team — Thu, 04 Mar 2021 11:57:23 +0000

In every phase of the process Pietro Fiorentini grants the efficiency of the plants with every kind of operation and maintenance, scheduled or on call, made by professional personnel.
We follow every plant in all its phases, offering our services to ensure continuity, efficiency, quality, low cost management of all the requested and provided actions by scheduled maintenance and functional tests to the gas pressure reducing stations, mechanical overhaul of reducing lines (SSV, PCV,PSV, etc.), flue gas emission and overhaul of Water Bath Heater (burner, fuel gas ramp, BMS panel, etc.).

The post Operations & maintenance appeared first on Pietro Fiorentini.

Water bath heater supervision of inspection

Digital Team — Thu, 04 Mar 2021 11:56:36 +0000

The Water Bath Heater supervision of inspection service by Pietro Fiorentini, according to drawings and design codes, can verify the efficiency of WBH, flue gas emission, water quality, and dimensional check of the following key components:

process coil, that will be removed in case of damage only;
fire tube (furnace), that will be removed;
stack, that will be disassembled.
This activity includes flue gas emission check by using a certified portable instrument, decommissioning, supervision of inspection and commissioning.

The post Water bath heater supervision of inspection appeared first on Pietro Fiorentini.

Site survey

Digital Team — Thu, 04 Mar 2021 11:55:41 +0000

Pietro Fiorentini’s service field engineering teams conduct full site surveys and provide conditions reports for all equipments installed in the plant.
Site surveys also includes reviews of customer training needs and spare stock levels recommendation.

The post Site survey appeared first on Pietro Fiorentini.

Supervision, pre-commissioning, commissioning, start up

Digital Team — Thu, 04 Mar 2021 11:54:38 +0000

Our main target is supervising the mechanical and electrical installation of all functional units of the plant.
Once all the supervision is checked, Pietro Fiorentini provides the commissioning of all equipment of the plant in accordance with the relevant specs, drawings, codes of practice and international regulations.

The post Supervision, pre-commissioning, commissioning, start up appeared first on Pietro Fiorentini.

Automatic Meter Reading (AMR)

Digital Team — Thu, 04 Mar 2021 11:48:21 +0000

In the field of gas smart metering, our target is to grant a combination of innovative, precise and effective solutions with a wide range of products and services that monitor and collect data on each single plant. We rely on our experience, know-how, research and development to bring on modernization and commissioning actions.
We are aware of the importance of offering the most accurate Automatic Meter Reading (AMR), and we have boasted our best human and technological resources to deliver tailored solutions to ensure reliability in the data acquisition process:

a complete range of metering devices designed to meet the needs of the modern gas industry;
integrated measurement systems designed and manufactured relying on the experience of the greatest manufacturer of gas measurement and reduction plants in the world;
periodic calibration services.

The post Automatic Meter Reading (AMR) appeared first on Pietro Fiorentini.

Remote management

Digital Team — Thu, 04 Mar 2021 11:47:23 +0000

Rapid availability of reliable information is a fundamental requirement nowadays. The services offered by Pietro Fiorentini in terms of data acquisition and remote management daily contribute to improve process efficiency, optimizing the related costs. We help our customers to be constantly informed of what happens on-site, enabling prompt decision-making.
Thanks to our data center based in Rosate (Milan), we monitor the plants continuously, automatically and promptly reporting any anomalies, being able to take care of on-site emergencies.

The post Remote management appeared first on Pietro Fiorentini.

Engineering Procurement & Construction Management (EPCM)

Digital Team — Thu, 04 Mar 2021 11:45:43 +0000

Together with the traditional EPC formula, Pietro Fiorentini may provide Engineering, Procurement and Construction Management projects (EPCM). Our engineering skills, together with our management capabilities give the best solution in terms of flexibility for the customer.
On top, our partners may rely on Pietro Fiorentini’s worldwide service network: a highly skilled team of service specialists that ensure on time support online and on-site, for both scheduled and extraordinary plant management and maintenance.

The post Engineering Procurement & Construction Management (EPCM) appeared first on Pietro Fiorentini.

Engineering Procurement & Construction (EPC)

Digital Team — Thu, 04 Mar 2021 11:45:15 +0000

Engineering, Procurement and Construction (EPC) contracts are one of the most widespread type of contract used to commit works in the Oil & Gas industry.
Thanks to the engineering capabilities based in Milan and Vicenza offices, to the manufacturing premises in Vicenza and to the capillary network of service officers all around the world, Pietro Fiorentini ensures to its customers detailed design projects, solid and fast deliveries on-site, supervision of construction activiities on-site by coordinating civil, mechanical and electrical works, and finally we carry out pre-commissioning and commissioning activities before performing the Site Acceptance Test that demonstates compliance with contractual performance guarantees. In one word, we can successfully deliver turnkey plants.

The post Engineering Procurement & Construction (EPC) appeared first on Pietro Fiorentini.

Front end engineering design

Digital Team — Thu, 04 Mar 2021 11:44:20 +0000

Front end engineering design (FEED) is an engineering design framework used for an in-depth check of a project cost. The main target of this approach is to analyse project requirements, fix a design basis, freeze the process design and involve all main subvendors. At the end of this execise the FEED provides a detailed cost summary, that will allow contractors and suppliers to issue a firm quotation.
FEED process is handled by Pietro Fiorentini multidisciplinary team that takes into consideration all important aspects related to the project. Main objectives include definition of civil, mechanical and process engineering, carry out preliminary HAZOP & SIL, prepare main equipment list and data sheet of critical items, develop 2D & 3D preliminary models and finally automation strategy.
The main scope of FEED is to deliver a clear picture of all project constraints, i.e. technical aspects, safety & environmental issues and accordingly a deep evaluation of capital and operation costs.

The post Front end engineering design appeared first on Pietro Fiorentini.

Feasibility studies

Digital Team — Thu, 04 Mar 2021 11:43:30 +0000

Pietro Fiorentini is able to develop preliminary feasibility studies for various projects in the natural gas and renewable energy field. Our process solutions range in the entire supply chain, from upstream to downstream and including also the final distribution.
Our team of proposals, cost estimators and engineers is able to evaluate all the aspects that have to be addressed in the feasibility study:

functional and technical aspects;
analysis of specific site requirements (availabable utilities, revamping within existing units, etc.);
environmental constraints (environmental limitations or similar);
economical features of the project, including analysys of CAPEX, OPEX and ROI.

The post Feasibility studies appeared first on Pietro Fiorentini.

CNG daughter stations

Digital Team — Thu, 04 Mar 2021 11:29:49 +0000

CNG daughter station brings the advantage to provide gas in areas where pipelins are not present, keeping unchanged the safety and reliability of the system in order to respect all the international standards.
CNG daughter stations can work with a maximum pressure of 250 bar and they are able to meet all requests of downstream pressure needed to more common applications on the market.

The post CNG daughter stations appeared first on Pietro Fiorentini.

High pressure stations

Digital Team — Thu, 04 Mar 2021 11:29:00 +0000

Natural gas is usually highly pressurized as it flows through transmission pipelines, but once it reaches the consumers, it needs to be brought up to the contractual specifications for delivery. This often means that in high pressure stations solids and liquids have to be filtered out, the pressure has to be reduced, and the gas may need to be preheated to compensate the cooling effect of the pressure reduction (Joule-Thomson effect). Moreover, the downstream consumers need to be protected for over-pressurization from the transmission line.
An accurate pressure control is the main contributor to the smooth flow of gas into transmission lines. The wide range of models allows to choose always the most suitable product for each application, because 80 years of experience in the field tell us that not all applications have the same maintenance and silent operations.

The post High pressure stations appeared first on Pietro Fiorentini.

Gas metering

Digital Team — Thu, 04 Mar 2021 11:26:20 +0000

Gas metering stations are located along gas distribution and transmission networks. These stations allow pipeline operators and local distribution companies to monitor, manage, and account for the natural gas flowing through the network.
The main scope of a gas metering station is to measure the flow of gas, allowing distribution companies to manage the network and gas sellers to allocate and bill the consumption.
The flow rate through a station can be measured by means of different devices such as rotary, turbine and ultrasonic meters and orifice fittings. They record the flow rate in actual cubic meters and a volume converter calculates the equivalent compendated for pressure, temperature and density.

The post Gas metering appeared first on Pietro Fiorentini.

Odomatic – Electronic dosing odorizing pump system

Digital Team — Thu, 04 Mar 2021 11:18:35 +0000

The electronic dosing odorizing pump system Odomatic by Pietro Fiorentini has been designed specifically to guarantee a constant degree of odorization of gas independently from flow rate, type, or odorant use and from the degree of odorization required, avoiding all the inconvenience caused by traditional lapping systems.
Odomatic system mainly guarantees:

a constant degree of odorization in time, independent from flow rate of gas;
control and measurement of the quantity of liquid odorizer injected to the network by means of flow switch and/or flowmeter;
hourly, daily and monthly printouts of reports showing the average odorization rate, the quantity injected and the volume of gas output.

The post Odomatic – Electronic dosing odorizing pump system appeared first on Pietro Fiorentini.

OLF – Lapping odorizing system

Digital Team — Thu, 04 Mar 2021 11:18:06 +0000

The lapping odorizing system OLF by Pietro Fiorentini consists of a tank containing odorant in liquid state. Natural gas passes through the vessel, and, through contact with the vaporous part of the odorant, becomes suitable for injection.
This solution can be used with mono component type odorants, and odorants made up of mixtures of components having similar vapor pressures. It is available with a total capacity of 24, 125, 185 or 265 liters, and is suitable for a maximum working pressure up to 85 bar.

The post OLF – Lapping odorizing system appeared first on Pietro Fiorentini.

Dosafit – Electronic odorizing system

Digital Team — Thu, 04 Mar 2021 11:17:27 +0000

Based on the principle of controlled injection of odorizer, Dosafit is the electronic odorizing system by Pietro Fiorentini that relies on gas pressure instead of relying on separate injection pumps.
Dosafit is usually paired with OLF, the lapping odorizing system that stores the odorizer and acts as a backup in case of failure.
Dosafit guarantees:

a constant odorization rate over time independently from variations in the gas flow rate;
control and metering of the quantity of odorizer liquid put into the pipeline by the capacity level;
remote display of the actual odorizer level in the lapping odorizing system;
automatic intervention in the event of failure and/or power blackout;
possibility of transmitting all the distribution data and alarms through the phone line.

The post Dosafit – Electronic odorizing system appeared first on Pietro Fiorentini.

Gas purification by membranes

Digital Team — Thu, 04 Mar 2021 11:09:45 +0000

In gas purification, membranes are used to separate components in natural gas such as water, CO2 and hydrocarbons according to their permeabilities. Each gas component entering the membrane unit has a characteristic permeation rate that is a function of its ability to dissolve in and diffuse through the membrane.
The driving force for separation of a gas component in a mixture is the difference between its partial pressure across the membrane. As high pressure feed gas flows into the metal shell of the membrane unit, the fast components, such as water and CO2, permeate through the membrane.
This permeate stream is collected at a reduced pressure, while the retentate, i.e., the dry natural gas, leaves the separator at a slightly lower pressure than the feed.
Pietro Fiorentini offers this technology both in natural gas and in biogas purification applications.

The post Gas purification by membranes appeared first on Pietro Fiorentini.

Gas heat exchangers (KSI)

Digital Team — Thu, 04 Mar 2021 11:09:17 +0000

KSI standard design has been developed by Pietro Fiorentini to preheat upstream gas regulation sections, in order to compensate cooling due to Joule Thomson effect. The standard design is based on a vertical BEU configuration with gas flowing through the tubes and heating medium on the shell side.
Pietro Fiorentini gas heat exchangers (KSI) are suitable for natural gas, air, propane and other non-aggressive gases, and can be provided with hot, superheated water or steam as heating fluid, based on customer’s needs.
On demand, they can be equipped with pressure gauge and pressure switch, safety valve on tube or shell side and with air self-exhausting device.

The post Gas heat exchangers (KSI) appeared first on Pietro Fiorentini.

Gas indirect water/glycol bath heaters

Digital Team — Thu, 04 Mar 2021 11:08:35 +0000

Gas indirect water/glycol bath heaters by Pietro Fiorentini have a wide variety of successful applications in oil & gas production, processing and transmission industry.
Some of the most common applications include:

gas dew point heating to prevent condensation phenomena due to the Joule-Thomson effect;
heating of high-pressure natural gas pressure regulation or fuel gas super-heating for upstream gas turbines, to prevent external icing formation;
gas heating for downstream low temperature storages;
viscosity reduction, to facilitate degassing and dewatering of crude oil heating upstream treatments.
These devices can be realized with forced draft and natural draft, with coils as per API 12K or with U tube bundles, with a highly variable duty ranging from 90 kW up to 12.5 MW.

The post Gas indirect water/glycol bath heaters appeared first on Pietro Fiorentini.

Gas filtering units

Digital Team — Thu, 04 Mar 2021 11:08:11 +0000

The stream of natural gas spans from the wellhead to the doorstep of each single end user, and the first task of each company operating along this path is to grant safety in each step. Ensuring a reliable gas transmission and distribution means injecting clean gas along the pipeline.
Gas filtering units by Pietro Fiorentini are designed to meet customer specifications and use the most suitable technology for every situation, such as:

gravity separation, where different phases of a mixed stream decant and form interface levels between phases due to gravity;
impingement separation, where a drop of liquid hits an obstacle and adheres to it, coalescing with other droplets;
centrifugation separation, where rotational effects and gravity are used to separate mixtures of solids and fluids (cyclones);
coalescing separation, where small droplets of non-gaseous media are removed from the gas through elements such as fiberglass cartridges.

The post Gas filtering units appeared first on Pietro Fiorentini.

FioMinor

Digital Team — Thu, 04 Mar 2021 09:53:18 +0000

Orifice fitting by Pietro Fiorentini, FioMinor is a volumetric measuring system based on the voluntary introduction of a concentrated pressure drop through a stainless steel disc provided with a calibrated hole. This device allows an easy replacement of the disc after interrupting the gas flow in the pipe section where it is installed.

Typically installed in the main piping of high-pressure transmission systems and medium pressure natural gas distribution networks, it can be used with previously filtered gas.

The post FioMinor appeared first on Pietro Fiorentini.

FioMaster

Digital Team — Thu, 04 Mar 2021 09:52:34 +0000

The orifice fitting FioMaster by Pietro Fiorentini is a volumetric measuring system based on the voluntary introduction of a concentrated pressure drop through a stainless steel disc with a calibrated hole.
The design of this device allows the disc to be replaced without interrupting the gas flow.

It can be used with previously filtered gas and is generally installed in the main pipelines of high-pressure transmission systems and medium pressure natural gas distribution networks.

The post FioMaster appeared first on Pietro Fiorentini.

FioSonic

Digital Team — Thu, 04 Mar 2021 09:51:17 +0000

FioSonic, the Ultrasonic Flow Meter for gas transmission networks, completes Pietro Fiorentini range of products dedicated to the industrial sector.
With its multi path-chordal technology, it provides real time diagnostics, high accuracy and redundancy for fiscal gas flow measurement.

Suitable for use with dry, wet, corrosive and abrasive gases, but also with gas such as sour gas or biogas with H2S, it is mainly used for high-pressure transmission systems and for medium pressure natural gas distribution networks.

FioSonic is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post FioSonic appeared first on Pietro Fiorentini.

IM-RM

Digital Team — Thu, 04 Mar 2021 09:49:32 +0000

Approved for use in fiscal measurement, IM-RM is the Rotary Gas Meter by Pietro Fiorentini characterized by constant and repeatable accuracy. It is mainly used in high-pressure transmission systems and in medium and low pressure natural gas distribution networks.

It can be used with non-corrosive, filtered and dry gases, including specialty gases.

IM-RM is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post IM-RM appeared first on Pietro Fiorentini.

IM-TM

Digital Team — Thu, 04 Mar 2021 09:47:41 +0000

Designed to measure gas velocity, the IM-TM turbine meter by Pietro Fiorentini incorporates an innovative method of conditioning flow in the meter body, within which a straightening section aligns the gas flow by removing undesired swirls and turbulence before they reach the turbine rotor.

Suitable for measuring non-corrosive, filtered and dry gases, including specialty gases, it is mainly used in high-pressure transmission systems and in medium and low pressure natural gas distribution networks.

IM-TM is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post IM-TM appeared first on Pietro Fiorentini.

HFA – HFB filters

Digital Team — Thu, 04 Mar 2021 09:33:04 +0000

The HFA – HFB by Pietro Fiorentini is a dry gas filter which can be used with natural and manufactured gas, air, propane and other non-aggressive gases.

This device is mainly used for high-pressure transmission systems and for medium pressure natural gas distribution networks.

HFA – HFB filter is Hydrogen Ready for NG-H₂ blending.

The post HFA – HFB filters appeared first on Pietro Fiorentini.

VS/AM 65

Digital Team — Thu, 04 Mar 2021 09:26:06 +0000

Direct-operated relief valve, VS/AM 65 by Pietro Fiorentini is a safety device which vents gas when the system pressure exceeds the set value due to temporary events, such as expansion due to rise in gas temperature or downstream pressure shocks caused by sudden changes of flow rate.

Strongly recommended for medium and low pressure gas distribution networks, this device can be used with natural gas and previously filtered non-corrosive gases.

Click here to see the product page in the 100% hydrogen version.

The post VS/AM 65 appeared first on Pietro Fiorentini.

VS/AM 58

Digital Team — Thu, 04 Mar 2021 09:25:19 +0000

The direct-operated relief valve VS/AM 58 by Pietro Fiorentini is a safety device which vents gas when the system pressure exceeds the set value due to temporary events, such as expansion due to rise in gas temperature or downstream pressure shocks caused by sudden changes of flow rate.

Particularly suitable in high-pressure transmission systems and in medium pressure gas distribution networks, this device can be used with natural gas and previously treated, non corrosive gaseous fluids.

Click here to see the product page in the 100% hydrogen version.

The post VS/AM 58 appeared first on Pietro Fiorentini.

PVS 803

Digital Team — Thu, 04 Mar 2021 09:24:29 +0000

PVS 803 is the pilot-operated relief valve by Pietro Fiorentini in which the opening and the closing of the main plug is controlled by a pilot device which is very sensitive to the variations of the in-line pressures.

Mainly used in high-pressure transmission systems and in medium pressure gas distribution networks, this device can be used with natural gas and previously treated, non corrosive gaseous fluids.

The post PVS 803 appeared first on Pietro Fiorentini.

PVS 782

Digital Team — Thu, 04 Mar 2021 09:24:04 +0000

In the pilot-operated relief valve PVS 782 by Pietro Fiorentini, the opening and the closing of the main plug is controlled by a pilot device which is very sensitive to the variations of the in-line pressures.

Particularly suitable for high-pressure transmission systems and for medium pressure gas distribution networks, this device can be used with natural gas and previously treated, non corrosive gaseous fluids.

The post PVS 782 appeared first on Pietro Fiorentini.

Dilock

Digital Team — Thu, 04 Mar 2021 09:23:37 +0000

The slam shut valve Dilock by Pietro Fiorentini is a safety device which quickly intercepts gas flow when the controlled pressure reaches a pre-set limit due to any anomaly in the system, or when required by the operator at the installation point or from a remote point.

Strongly recommended for medium and low pressure gas distribution networks, this device can be used with natural gas and previously filtered non-corrosive gases.

Dilock is Hydrogen Ready for NG-H₂ blending.

The post Dilock appeared first on Pietro Fiorentini.

SCN

Digital Team — Thu, 04 Mar 2021 09:23:17 +0000

The slam shut valve SCN by Pietro Fiorentini is a compact safety device which quickly intercepts gas flow whenever the pressure under monitoring reaches a pre-set limits, or whenever manually required by operator on-site or through a remote command (optional device).

Suitable for use with natural gas and previously filtered non-corrosive gases, this device is strongly recommended for medium and low pressure gas distribution networks.

SCN is Hydrogen Ready for NG-H₂ blending.

The post SCN appeared first on Pietro Fiorentini.

SSX 176

Digital Team — Thu, 04 Mar 2021 09:22:45 +0000

The slam shut valve SSX 176 by Pietro Fiorentini is a compact safety device which quickly intercepts gas flow whenever the pressure under monitoring reaches a pre-set limits, or whenever manually required by operator on-site or through a remote command (optional device).

Suitable for use with natural gas and previously filtered non-corrosive gases, it is mainly used for high-pressure transmission systems and for medium pressure gas distribution networks.

The post SSX 176 appeared first on Pietro Fiorentini.

HBC 975

Digital Team — Thu, 04 Mar 2021 09:22:28 +0000

The slam shut valve HBC 975 by Pietro Fiorentini is a safety device which quickly intercepts gas flow when the pressure it is monitoring reaches a pre-set limit due to any anomaly in the system, or when required by the operator at the installation point or from a remote point.

Particularly suitable for high-pressure transmission systems, this device can be used with natural gas and previously treated, non corrosive gaseous fluids.

HBC 975 is Hydrogen Ready for NG-H₂ blending.

The post HBC 975 appeared first on Pietro Fiorentini.

SBC 782

Digital Team — Thu, 04 Mar 2021 09:21:35 +0000

The slam shut valve SBC 782 by Pietro Fiorentini is a safety device which quickly intercepts gas flow when the pressure it is monitoring reaches a pre-set limit due to any anomaly in the system, or when required by the operator at the installation point or from a remote point.

Particularly suitable for high-pressure transmission systems and for medium and low pressure gas distribution networks, this device can be used with natural gas and previously treated, non corrosive gaseous fluids.

SBC 782 is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post SBC 782 appeared first on Pietro Fiorentini.

SBC 187

Digital Team — Thu, 04 Mar 2021 09:20:54 +0000

The slam shut valve SBC 187 by Pietro Fiorentini is a safety device which immediately intercepts gas flow when the pressure it is monitoring reaches a pre-set limit due to any anomaly in the system, or when enabled manually.

Mainly used for high-pressure transmission systems and for medium pressure gas distribution networks, this device can be used with natural gas and previously treated, non-corrosive gaseous fluids.

SBC 187 is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post SBC 187 appeared first on Pietro Fiorentini.

Syncroflux

Digital Team — Thu, 04 Mar 2021 09:12:35 +0000

The Syncroflux regulating valve by Pietro Fiorentini is a bypass and throttling device is characterized by a soft insert on the valve seats for better tightness and a balanced shutter for easier opening and closing. It has a top-entry body suitable for flanged coupling.

Suitable for use with natural gas and previously treated, non-corrosive gaseous fluids, this device is mainly used in high-pressure transmission systems and in medium pressure gas distribution networks.

The post Syncroflux appeared first on Pietro Fiorentini.

VLM

Digital Team — Thu, 04 Mar 2021 09:12:17 +0000

VLM valve by Pietro Fiorentini is a bypass and throttling device characterized by a soft insert on the valve seats for better tightness and a balanced shutter for easier opening and closing. The top-entry body is suitable for flanged coupling.

This device is mainly used in high-pressure transmission systems and in medium pressure gas distribution networks and it is suitable for use with natural gas and previously treated, non-corrosive gaseous fluids.

VLM is Hydrogen Ready for NG-H₂ blending.

The post VLM appeared first on Pietro Fiorentini.

Reflux 919

Digital Team — Thu, 04 Mar 2021 09:12:01 +0000

Reflux 919 by Pietro Fiorentini is a control diaphragm valve especially designed for natural gas or other preliminarily filtered non-corrosive gases. It may be supplied in the direct-action (air to close), or in the reverse action type (air to open).

This device is mainly used in high-pressure transmission systems and in medium pressure gas distribution networks.

The post Reflux 919 appeared first on Pietro Fiorentini.

Deltaflux

Digital Team — Thu, 04 Mar 2021 09:11:38 +0000

The control ball valve Deltaflux is the ideal solution for all fluid control applications where high differential pressure or great flow rates are involved.
The refined design of the rotating trim allows simultaneously high flow rate coefficients Cv and minimum pressure drops in fully open position.

This device, particularly suitable for high-pressure transmission systems and for medium pressure distribution networks, can be used with natural gas and previously filtered non-corrosive gases.

For the Pietro Fiorentini Group, valves are produced by TIV Valves, a Group company specialized in the production of valves based in Rescaldina (MI). For more information visit the website.

The post Deltaflux appeared first on Pietro Fiorentini.

Trunnion ball valves

Digital Team — Thu, 04 Mar 2021 09:11:00 +0000

The ball of the floating valve is mounted on a trunnion which supports the pressure load. The seats are spring energized and the body construction is one piece, made by forging or casting. The ball is inserted from the top and it’s possible to disassembly the valve in line.

Mainly used for high-pressure transmission systems and for medium pressure gas distribution networks, it can be used with natural gas and previously filtered non-corrosive gases.

The trunnion ball valves are Hydrogen Ready for NG-H₂ blending.

For the Pietro Fiorentini Group, valves are produced by TIV Valves, a Group company specialized in the production of valves based in Rescaldina (MI). For more information visit the website.

The post Trunnion ball valves appeared first on Pietro Fiorentini.

Floating ball valves

Digital Team — Thu, 04 Mar 2021 09:10:30 +0000

In the floating valve the ball is not rigidly held on its rotational axis and so is free to float between seats. Sealing is achieved by the action of the pressure, which pushes the ball against a seat and the body construction is two pieces, bolted joint, made by forging, forged or rolled bar.

Mainly used for high-pressure transmission systems and for medium pressure gas distribution networks, it is suitable for use with natural gas and previously filtered non-corrosive gases.

The floating ball valves are Hydrogen Ready for NG-H₂ blending.

For the Pietro Fiorentini Group, valves are produced by TIV Valves, a Group company specialized in the production of valves based in Rescaldina (MI). For more information visit the website.

The post Floating ball valves appeared first on Pietro Fiorentini.

BF 32

Digital Team — Thu, 04 Mar 2021 09:09:50 +0000

The butterfly valve BF 32 is an interception device able to guarantee low pressure losses. It may be used also for intercepting liquids when a hermetic seal, low pressure losses and compact construction in the flow direction are required.

Suitable for use with natural gas and previously filtered non-corrosive gases, it is mainly used in medium and low pressure gas distribution networks.

For the Pietro Fiorentini Group, valves are produced by TIV Valves, a Group company specialized in the production of valves based in Rescaldina (MI). For more information visit the website.

The post BF 32 appeared first on Pietro Fiorentini.

BF 31

Digital Team — Thu, 04 Mar 2021 09:09:36 +0000

The butterfly valve BF 31 is an interception device able to guarantee low pressure losses. It may be used also for intercepting liquids when a hermetic seal, low pressure losses and compact construction in the flow direction are required.

Suitable for use with natural gas and previously filtered non-corrosive gases, it is mainly used in medium and low pressure gas distribution networks.

For the Pietro Fiorentini Group, valves are produced by TIV Valves, a Group company specialized in the production of valves based in Rescaldina (MI). For more information visit the website.

The post BF 31 appeared first on Pietro Fiorentini.

Dival 700

Digital Team — Thu, 04 Mar 2021 08:36:34 +0000

Direct-operated gas pressure regulator controlled by a diaphragm and contrasting regulated spring action, Dival 700 is suitable for use with previously filtered non-corrosive gases.

Its use is strongly recommended in medium and low pressure natural gas distribution networks.

According to the European Standard EN 334, it is classified as Fail Open.

Dival 700 is Hydrogen Ready for NG-H₂ blending.

The post Dival 700 appeared first on Pietro Fiorentini.

Staflux Mini

Digital Team — Wed, 03 Mar 2021 17:24:56 +0000

Staflux Mini is a direct-operated pressure regulator controlled by a diaphragm and contrasting regulated counter pressure action.

Mainly used for high-pressure transmission systems and for medium pressure natural gas distribution networks, it can be used with previously filtered non-corrosive gases.

According to the European Standard EN 334, it is classified as Fail Close.

The post Staflux Mini appeared first on Pietro Fiorentini.

Staflux 187

Digital Team — Wed, 03 Mar 2021 17:22:22 +0000

Staflux 187 is a direct-operated pressure regulator controlled by a diaphragm and contrasting regulated counter pressure action.

It can be used with previously filtered non-corrosive gases and is particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks.

According to the European Standard EN 334, it is classified as Fail Open.

Staflux 187 is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post Staflux 187 appeared first on Pietro Fiorentini.

Staflux 185

Digital Team — Wed, 03 Mar 2021 17:19:40 +0000

Staflux 185 is a direct-operated gas pressure regulator controlled by a diaphragm and contrasting regulated counter pressure action.

This device is particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks. It can be used with previously filtered non-corrosive gases.

According to the European Standard EN 334, it is classified as Fail Open.

The post Staflux 185 appeared first on Pietro Fiorentini.

Dival 160 AP

Digital Team — Wed, 03 Mar 2021 17:16:31 +0000

Dival 160 AP by Pietro Fiorentini is a direct-operated gas pressure regulator controlled by a diaphragm and contrasting regulated spring action.

Classified as Fail Open according to the European Standard EN 334, it can be used with previously cleaned gaseous fluids. It is particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks.

Dival 160 AP is Hydrogen Ready for NG-H₂ blending.

The post Dival 160 AP appeared first on Pietro Fiorentini.

ATF

Digital Team — Wed, 03 Mar 2021 17:13:22 +0000

ATF Anti-Freeze is a direct-operated pressure regulator suitable with natural gas and all non-corrosive gases.

Easy to use and mantain, it is mainly used for medium pressure natural gas distribution networks.

The post ATF appeared first on Pietro Fiorentini.

Reflux 819/FO

Digital Team — Wed, 03 Mar 2021 17:08:10 +0000

Reflux 819/FO is a pilot-operated gas pressure regulator classified as Fail Open according to the European Standard EN 334.

Its use is strongly recommended in high-pressure transmission systems and in medium pressure natural gas distribution networks. It is suitable for use with previously filtered non-corrosive gases.

Reflux 819/FO is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post Reflux 819/FO appeared first on Pietro Fiorentini.

Reflux 819

Digital Team — Wed, 03 Mar 2021 17:01:34 +0000

Reflux 819 is a pilot-operated gas pressure regulator.

It is particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks, and it can be used with previously filtered non-corrosive gases.

According to the European Standard EN 334, it is classified as Fail Close (pilot series 200/A) or Fail Open (pilot series 210/A) according to the installed pilot (except for the PM819 monitor).

Reflux 819 is Hydrogen Ready for NG-H₂ blending.

Click here to see the product page in the 100% hydrogen version.

The post Reflux 819 appeared first on Pietro Fiorentini.

Dixi AP

Digital Team — Wed, 03 Mar 2021 16:54:07 +0000

Pilot-operated pressure regulator produced by Pietro Fiorentini, Dixi AP is suitable for use with previously filtered non-corrosive gases.

It is mainly used for high-pressure transmission systems and for medium pressure natural gas distribution networks.

According to the European Standard EN 334, it is classified as Fail Close.

The post Dixi AP appeared first on Pietro Fiorentini.

ASX 176/FO

Digital Team — Wed, 03 Mar 2021 16:48:00 +0000

ASX 176/FO is one of the pilot-operated pressure regulators by Pietro Fiorentini that are suitable for use with previously filtered and non-aggressive gaseous fluids.

Its use is strongly recommended in high-pressure transmission systems and in medium pressure natural gas distribution networks.

According to the European Standard EN 334, it is classified as Fail Open.

The post ASX 176/FO appeared first on Pietro Fiorentini.

ASX 176

Digital Team — Wed, 03 Mar 2021 16:40:43 +0000

The pilot-operated pressure regulator ASX 176 can be used with previously filtered and non-aggressive gaseous fluids.

According to the European Standard EN 334, it is classified as Fail Close. It is particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks.

The post ASX 176 appeared first on Pietro Fiorentini.

Aperflux 851

Digital Team — Wed, 03 Mar 2021 16:38:22 +0000

Aperflux 851 is one of the pilot-operated gas pressure regulators by Pietro Fiorentini.

This device is suitable for use with previously filtered non-corrosive gases, and it is mainly used for high-pressure transmission systems and for medium pressure natural gas distribution networks.

According to the European Standard EN 334, it is classified as Fail Open.

Aperflux 851 is Hydrogen Ready for NG-H₂ blending.

The post Aperflux 851 appeared first on Pietro Fiorentini.

Aperflux 101

Digital Team — Wed, 03 Mar 2021 16:34:25 +0000

Aperflux 101 is a piloted-operated pressure regulator.

Particularly suitable for high-pressure transmission systems and for medium pressure natural gas distribution networks, it can be used with previously filtered non-corrosive gases.

It is classified as Fail Open according to the European Standard EN 334.

The post Aperflux 101 appeared first on Pietro Fiorentini.